[fabianfred]

I have just got it to work with my Win7 install.
What do i have to do to use it in il2?
Are there changes to the conf.ini or what.... and which version of the 6DOF mod do i use or should I turn it off?...using single point ATM

[Messer]

Using FreeTrack 2.2 with a custom made three-point TrackIR device on WinXp 64. I just installed FreeTrack , callibrated the device to my preferences and launched Il-2 - nothing to change, it automatically found the game.
Works with and without 6DoF (though I definately prefer the experience with the mod on). Hope this help!

[marmusman]

I just got my FreeTrack running about a month ago. I did the same as Messer, I didn;t have to change anything in IL-2, is just worked. I use it with AAA UI1.1 mods. I do not think you get 6DOF with single point. With single point it will only give you side to side movement, I believe. You need 3 point for 6DOF. Maybe the 6DOF mod in IL-2 needs to have freetrack set for 6DOF?

One piece of advice for when you get it working in IL-2: the freetrack becomes the default "joystick" and your flight joystick will not work at first. So you need to manually re-assign all your joystick commands in the HOTAS settings (located bottom of the command list).

[fabianfred]

I just changed TrackIRuse=0 to 1 in conf.ini
It is Ok but jerky
How do I keep a full range of movement and smooth it down?
and make a dead zone in the centred position.

Perhaps i should try to have il2 and Freetrack running on different cores of my CPU.... but don't know how to achieve that..

[Strafe]

Hi. Are you using the last software version ?

The moviment behavior depends on your webcam model.
I'll send to you my profile. I has some adjustments to birng movoments smooth and wide. I hope it works for you.
Pls send me your e-mail in PVT .

regards,

[Goblin]

Fabian, to make less jerky try to set point view of led with GREEN FPS and JPS counter stable 28-30 fps ,to obtain this you HAVE TO DO:
1- SET AUTO EXPOSURE to NO (UNTIK the little square on the camera) AND value of exposure to 0-1 (very low)
2- put your CAMERA BRIGHTNESS very low + CONTRAST HIGH
3 - put a photo negative piece on the camera lens and if possible remove IR filter
4- move the threshold slide to left-right a bit with the hat on your head till you have STABLE the all three little point of your hat

- to have dead zone set a initial range of cuves almost 90

[.041 Safety Wire]

Fabian,

I use the single point also and find it more than adequate for playing IL2. If you send me your email I will send you my profile. I am using 2.1 and find it very smooth I think you will find you do not need a deadzone once you get used to it. BTW webcam is a microsoft 3000 and I used a kids led nitelight and swapped led for ir led, with my setup I have webcam mounted on headset and 110V nitelie mounted above monitor. I did remove the ir filter from camera and made a vivible light filter from an old floppy disc and other recommended changes posted at freetrack sight. I consistently get 28 to 30fps .

http://www.free-track.net/english/

Here is a copy of my IL2 profile, you will most likely have to open one of the profile fgp files and delete and then add this and I said this is for 2.1 which works better for me than 2.2. If you need 2.1 I can email that to you also.

[Defaults]
Average=1
[Sensitivity]
Yaw=38
Pitch=38
Roll=1
X=1
Y=1
Z=1
[Deadzone]
Yaw=150
Pitch=150
Roll=1
X=100
Y=100
Z=1
Zooming=81
SmoothStableMultiplier=25
SmoothRawMultiplier=25
Dynamic=19
Point=10
[Inverted]
Yaw=0
Pitch=0
Roll=0
X=0
Y=0
Z=0
[AxisEnabled]
Yaw=1
Pitch=1
Roll=0
X=0
Y=0
Z=0
[YawCfg]
X0=0
Y0=167
X1=88
Y1=101
X2=551
Y2=164
X3=554
Y3=2
[PitchCfg]
X0=0
Y0=167
X1=191
Y1=97
X2=115
Y2=161
X3=552
Y3=2
[RollCfg]
X0=0
Y0=166
X1=122
Y1=128
X2=194
Y2=87
X3=514
Y3=2
[XCfg]
X0=0
Y0=167
X1=550
Y1=30
X2=202
Y2=50
X3=554
Y3=2
[YCfg]
X0=0
Y0=167
X1=156
Y1=5
X2=87
Y2=158
X3=553
Y3=2
[ZCfg]
X0=0
Y0=166
X1=206
Y1=151
X2=48
Y2=31
X3=554
Y3=2
[Output]
MouseX=0
MouseXEnabled=0
MouseY=0
MouseYEnabled=0
MouseWheel=0
MouseWheelEnabled=0
MouseAutoPan=0
MouseAbsolute=0
MouseWheelScale=50
PPJoyControllerNumber=1
TIR=1
Mouse=0
PPJoy=0
Keys=0
SimConnect=0
FS=0
[Mapping]
MiddleMouse=0
Center=
CenterBeep=1
CenterHold=0
Pause=
PauseBeep=1
PauseHold=1
SmoothStable=
SmoothStableBeep=1
SmoothStableHold=0
SmoothRaw=
SmoothRawBeep=1
SmoothRawHold=0
Yaw=
YawBeep=1
YawHold=0
Pitch=
PitchBeep=1
PitchHold=0
Roll=
RollBeep=1
RollHold=0
X=
XBeep=1
XHold=0
Y=
YBeep=1
YHold=0
Z=
ZBeep=1
ZHold=0
Mouse=
MouseBeep=1
MouseHold=0
Joystick=
JoystickBeep=1
JoystickHold=0
6DOF=
6DOFBeep=1
6DOFHold=0
SimConnect=
SimConnectBeep=1
SimConnectHold=0
Keymap=
KeymapBeep=1
KeymapHold=0
[OutputKeys]
YawThreshold=100
YawAutoPress=1
YawPos=
YawNeg=
PitchThreshold=83
PitchAutoPress=1
PitchPos=
PitchNeg=
RollThreshold=50
RollAutoPress=1
RollPos=
RollNeg=
XThreshold=50
XAutoPress=1
XPos=
XNeg=
YThreshold=50
YAutoPress=1
YPos=
YNeg=
ZThreshold=50
ZAutoPress=1
ZPos=
ZNeg=

Congo

[fabianfred]

Thanks for your replies guys...

I am using the new 2.2 software ATM...and a Logitec webcam...and can get it to work on Win7 but not XP (Freetrack crashes)